QUESTION 1
FCAPS is a network maintenance model defined by ISO. What does it stand for?
A. Action Management
B. Fault Management
C. Configuration Management
D. Protocol Management
E. Security Management
Answer: BCE
Explanation/Reference:
QUESTION 2
Which alerts will be seen on the console when running the command: logging console warnings.
A. warnings only
B. warnings, notifications, error, debugging, informational
C. warnings, errors, critical, alerts, emergencies
D. notifications, warnings, errors
E. warnings, errors, critical, alerts
Answer: C
Explanation/Reference:
QUESTION 3
You have 2 commands used for ftp:
ip ftp username xxxxxx
ip ftp password yyyyyy
Which two commands will be used when switching from ftp to http?
A. ip http username xxxxxx
B. ip http client username xxxxxx
C. ip http password yyyyyy
D. ip http client password 0 yyyyyy
E. ip http server username xxxxxx
F. ip http server password yyyyyy
Answer: BD
Explanation/Reference:
QUESTION 4
Which two of the following options are categories of Network Maintenance tasks?
A. Firefighting
B. Interrupt-driven
C. Policy-based
D. Structured
E. Foundational

 

Answer: BD
Explanation/Reference:
QUESTION 5
The following commands are issued on a Cisco router:
Router(config)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
Router(config)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1
Router#debug ip packet 199
What would be the output shown on the console?
A. All IP packets passing through the router
B. Only IP packets with the source address of 10.1.1.1
C. All IP packets from 10.1.1.1 to 172.16.1.1
D. All IP packets between 10.1.1.1 to 172.16.1.1
Answer: D
Explanation/Reference:
QUESTION 6
You have two NTP servers 10.1.1.1 & 10.1.1.2 and want to configure a router to use 10.1.1.2 as its NTP
server before falling back to 10.1.1.1. Which command will you use?
A. ntp server 10.1.1.1
ntp server 10.1.1.2
B. ntp server 10.1.1.1
ntp server 10.1.1.2 primary
C. ntp server 10.1.1.1
ntp server 10.1.1.2 prefer
D. ntp server 10.1.1.1 fallback
ntp server 10.1.1.2
Answer: C
Explanation/Reference:
QUESTION 7
The interface is up and protocol is up. What level of logging is enabled when you get these messages?
%LINEPROTO 5 UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up ‐‐
%LINKDOWN 3 SERIAL: ‐‐
A. alerts
B. errors
C. critical
D. notifications
Answer: D
Explanation/Reference:
QUESTION 8
Two Cisco routers are connected to each other and are enabled CDP. Serial line is up,protocol is also up,
but cdp neighbor not working. What layer of the OSI model does the problem most likely exist?

A. Physical
B. Session
C. Application
D. Data-Link
E. Network
Answer: D
Explanation/Reference:
QUESTION 9
The interface is up and protocol is up. When do u get these messages.
%LINKDOWN 3 SERIAL: ‐‐
%LINEPROTO 5 UPDOWN: Line protocol on Interface FastEthernet0/14, changed state to up ‐‐
A. the first message is a severity 3 log message
B.
C.
D.
Answer: A
Explanation/Reference:
QUESTION 10
what will happen if u configure two router as NTP server (something like that )
A. The router will choose the best reliable server and will synchronise with it.
B.
C.
D.
Answer: A
Explanation/Reference: